24 Failed to communicate with drive that appears registered with the operating system.
25 Warning - No Communication With Drive
26 Unable to communicate with the tape drive. Another application may currently have exclusive access to the drive. If this is the case, you will need to exit the Seagate Tape Diagnostic, shut down any applications accessing the tape drive, and then restart the Seagate Tape Diagnostic,
27 Approximately
28 on tape drive:
29 Test Read-Write
30 WARNING: ALL EXISTING DATA ON THIS TAPE WILL BE DESTROYED.\n\nPlease make sure that a scratch tape of the proper format is inserted into the drive and that the write-protect tab is in the Off position.\n
31 Test Read-Only
32 This operation requires a scratch tape of the proper format that has been previously written using the Test Read-Write command. The amount of data to be read must be the same or less than the amount that was previously written.\n\n
33 Test Hardware Compression
34 WARNING: ALL EXISTING DATA ON THIS TAPE WILL BE DESTROYED\nINCLUDING PREVIOUS READ-WRITE TESTS.\n\nPlease make sure that a scratch tape of the proper format is inserted into the drive and that the write-protect tab is in the Off position.\n
35 If compression has been tested since the last Read-Write test was performed, this Read-Only test will fail because the Compression test produces a different data set.
36 Test Data Value May Be Too High
37 The data value exceeds the useable area on the media.
38 The tape diagnostic utility has cancelled the previous operation. However, the current state of drive data compression is: OFF.\n\nWould you like to turn data compression on?
39 Tape Drive Data Compression
40 Received user input to CANCEL test.
41 Canceling Test
42 Cancellation complete.
43 Selected: Test Read-Only.
44 Selected: Test Read-Write.
45 Examining compression attributes.
46 Failure: End of Data (EOD) marker has been detected.
47 Failure: End of Partition (EOP) marker has been detected.
48 Failure: Check tape write protection.
49 Test less than
101 /
1011 &Test Read-Write
1012 Test &Read-Only
1013 Check &Media Capacity
1014 R&etension Tape
1015 Test Hardware &Compression
1119 &OK
59136 EXT
59137 CAP
59138 NUM
59139 SCRL
59140 OVR
59141 REC
59143 Test Title
59144 This is a test question.
59145 No Log File Selected
59146 No Log File has been selected in which to save the current messages.
59147 Save Messages
59148 The current messages appearing in the message log have not been saved and will be lost. Would you like to save them to the current Log File?
59149 Byte Entry Error
59150 The value entered must be an integer value and be greater than\nor equal to 5 MBytes (1 GByte, if GBytes is selected).\n\nIn either MBytes or GBytes, the actual number value should not\nexceed 2,147,483,647.
59151 Operating System Incompatible
59152 This utility is designed to work with the Windows 95, Windows 98, and Windows NT operating systems.
59153 No Log File Selected To Print
59154 A log file must be selected for printing. Open a log file or save the contents of any unsaved messages now appearing in the message log.
59155 Welcome to the Seagate Tape Diagnostic Utility
59156 This utility will test SCSI and IDE/ATAPI tape drives from Seagate, Conner and Archive.
59157 Please select a language
59158 Welcome
59159 The Seagate Tape Diagnostic has detected the following Seagate SCSI and/or ATAPI/IDE tape drive(s) attached to your system.
59160 Select a Tape Drive
59161 Seagate Tape Diagnostic 3.0 A
59162 Current Drive Selected
59163 Options Selected
59164 Operational Status
59165 Operations
59166 System Configuration Check
59167 !!! System Initialization in Progress !!!
59168 MBytes (uncompressed) remaining capacity
59169 Warning:
59170 not supported.
59171 Drive Not Supported
59172 Timeout Error
59173 The current tape drive operation timed-out before completing.
59174 System Message
59175 A system-level tape drive error has occurred. Click OK and view the message log for more detail.
59176 has occurred. See message log.
59177 System Failure
59178 Unable to load: Wnaspi32.dll. Exiting tape diagnostic utility. Please contact your system administrator.
59179 Unable to access Wnaspi32.dll support functions. Exiting tape diagnostic utility. Please contact your system administrator.
59180 Can't create an event during initialization using CreateEvent(). Exiting tape diagnostic utility. Please contact your system administrator.
59181 Unable to find host adapter
59182 The diagnostic tape utility may be in an unstable state.
59183 Selected: Check Media Capacity.
59184 Issued Cmd: Test Unit Ready.
59185 Is the correct tape loaded in the drive?
59186 Issued Cmd: Load Tape with Retension.
59187 Issued Cmd: Load Tape.
59188 Write Operation
59189 Issued Cmd: Write File Marks.
59190 Issued Cmd: Rewind Tape.
59191 Read Operation
59192 Issued Final Cmd: Rewind Tape.
59193 Issued Cmd: Write
59194 MB to tape.
59195 GB to tape.
59198 Issued Cmd: Read and Compare
59199 MB of data from tape.
59200 Selected: Retension Tape.
59201 Selected: Test Compression.
59202 Write Command Complete.
59203 Test failed. A Read/Compare error has been detected - possible read beyond the end of valid data.
59204 Test completed successfully.
59205 Test failed due to excessive errors.
59206 Retry the test with a different tape and/or clean the drive.
59207 GB of data from tape.
59209 Failure on: Load Tape
59210 Failure on: Retension Tape
59211 Tape retension complete.
59212 Failure on: Write File Marks
59213 Failure on: Rewind
59214 Failure on: Test For Unit Ready
59215 Failure on: Write Data to Drive.
59216 Failure on: Read Data From Drive
59217 Failure on: Read Position
59218 Failure on: Log Sense
59219 Failure on: Log Select Reset
59220 Tape drive compression is operating normally.
59221 Tape drive compression is turned-off, unable to perform compression check.
